SHARP LC-32SH20U SERVICE MODE AND ADJUSTMENTS

SHARP LC-32SH20U

WHEN REPLACING EEPROM (MEMORY) IC
CONFIRMATION OF CHECK SUM, POWER ON TOTAL HOURS, MICON VERSION AND DIGITAL TV MICON FIRMWARE
Initial total of MEMORY IC, POWER ON total hours, MICON VERSION and Digital TV MICON Firmware can be checked on the screen. Total hours are displayed in 16 system of notation.
1.Turn on the POWER, and set to the TV mode.
2.Set the VOLUME to minimum.
3.Press both VOL. DOWN button on the set and Channel button (8) on the remote control for more than 2 seconds.
4. After the confirmation of each check sum, POWER ON total hours, MICON VERSION and Digital TV MICON
Firmware, turn off the power.
CONFIRMATION OF INITIAL DATA
If a service repair is undertaken where it has been required to change the MEMORY IC, the following steps should be taken to
ensure correct data settings while making reference to INITIAL SETTING TABLE (Attached "INITIAL DATA").
1. Turn on the POWER, and set to the TV mode.
2. Set the VOLUME to minimum.
3. Press both VOL. DOWN button on the set and Channel button (6) on the remote control for more than 2 seconds.
4. ADDRESS is now selected and should "blink". Using the UP/DOWN buton on the remote, step through the ADDRESS
until required ADDRESS to be changed is reached.
5. Press RIGHT/LEFT button to select DATA. When DATA is selected, it will "blink".
6. Again, step through the DATA using UP/DOWN button until required DATA value has been selected.
7. Pressing RIGHT/LEFT button will take you back to ADDRESS for further selection if necessary.
8. Repeat steps 4 to 6 until all data has been checked.
9. When satisfied correct DATA has been entered, turn POWER off (return to STANDBY MODE) to finish DATA input.
After the data input, set to the initializing of shipping.
10. Turn POWER on.
11.Press both VOL. DOWN button on the set and Channel button (1) on the remote control for more than 2 seconds.
12. After the finishing of the initializing of shipping, the unit will turn off automatically.
The unit will now have the correct DATA for the new MEMORY IC.
BASIC ADJUSTMENTS
1. Set the VOLUME to minimum.
2. Press the VOL. DOWN button on the set and the channel button (9) on the remote control for more than 2 seconds to display adjustment mode on the screen
3.Use the UP/DOWN button or Channel button (0-9) onthe remote control to select the options
4. Press the MENU button on the remote control to end the adjustments.
5.To display the adjustment screen for AV, CS, HDMI mode, press the INPUT button on the remote control to set to the AV, CS, HDMI mode. Press the VOL.DOWN button on the set and the channel (9) on the remote control for more than 2 seconds.
WHITE BALANCE
1. Place the set in Aging Test for more than 15 minutes.
2. Receive the gray scale pattern from the Pattern Generator.
3. Press the INPUT button on the remote control to set to the AV mode.
4. Using the remote control, set the brightness and contrast to normal position.
5. Activate the adjustment mode display and press the channel button (03) on the remote control to select “R DRIVE (N)”.
6. Press the UP/DOWN button on the remote control to select the “R CUTOFF (N)”, “B DRIVE (N)”, “B CUTOFF (N)”, “R DRIVE (C)”, “R CUTOFF (C)”, “B DRIVE (C)”, “B CUTOFF (C)”, “R DRIVE (W)”, “R CUTOFF (W)”, “B DRIVE (W)” and “B CUTOFF (W)”.
7. Adjust the RIGHT/LEFT button on the remote control to whiten the R CUTOFF (N), B DRIVE (N), B CUTOFF (N), R DRIVE (C), R CUTOFF (C), B DRIVE (C), B CUTOFF (C), R DRIVE (W), R CUTOFF (W), B DRIVE (W) and B CUTOFF (W) at each step tone sections equally.
8. Perform the above adjustments 5 and 6 until the white color is looked like a white.
SERVICE MODE
To enter to the SERVICE MODE function, press and hold both buttons simultaneously on the main unit and on the remote control for more than the standard time in the appropriate condition.
Set Condition
Set Key
Remocon Key
Standard Time
Operations
TV mode

VOL. DOWN (Minimum)

0


2 sec.

Releasing of V-CHIP PASSWORD.


TV mode




VOL. DOWN (Minimum)




1




2 sec.



Initialization of factory TV data.
NOTE: If you set factory initialization, the memories are reset
such as the channel setting, and the POWER ON total
hours.

TV mode


VOL. DOWN (Minimum)


6


2 sec.


Can be checked of the INITIAL DATA of MEMORY IC.
Refer to the "WHEN REPLACING EEPROM (MEMORY) IC".


ALL mode



VOL. DOWN (Minimum)



8



2 sec.


Check of the SUM DATA, POWER ON total hours, MICON
VERSION and DIGITAL TV MICON FIRMWARE on the screen.
Refer to the "WHEN REPLACING EEPROM (MEMORY) IC".


ALL mode

VOL. DOWN (Minimum)

9

2 sec.
Display of the Adjustment MENU on the screen.
Refer to the "ELECTRICAL ADJUSTMENT" (On-Screen Display
Adjustment).