PANASONIC TX-L32ET5 SERVICE MODE AND LED BLINKING CODE

PANASONIC TX-L32ET5 

Technical Description
Specification of KEY for CI Plus, DTCP-IP, One-to-One, Widevine and Netflix
General information:

1. EEPROM (IC8902) for spare parts has the seed of KEY for each.
2. The final KEY data will be generated by LDA4 IC (IC8000) when SELF CHECK was done and are stored in both LDA4 IC
(IC8000) and EEPROM (IC8902).
All KEYs are not generated for all models.
The necessary KEY are only generated and stored depend on the feature of models.
Replacement of ICs:
When LDA4 IC (IC8000) is replaced, EEPROM (IC8902) should be also replaced with new one the same time.
When EEPROM (IC8902) is replaced, LDA4 IC (IC8000) is not necessary to be replaced the same time.
After the replacement of IC, SELF CHECK should be done to generate the final KEY data.
How to SELF CHECK: While pressing [VOLUME ( - )] button on the main unit, press the STATUS button on the remote control for more than 3 seconds.
TV will be forced to the factory shipment setting after this SELF CHECK.
USB HDD Recording:
General information:
Digital TV programmes can be recorded in USB HDD.
A One-to-One key generated in A-board by SELF CHECK binds TV and USB-HDD for communication.
That key is only one key for them. If the key is difference, TV can not access USB-HDD.
Caution:
New key will be generated by following SELF CHECK and previous TV programmes recorded in USB HDD will not be viewed.
SELF CHECK: While pressing [VOLUME ( - )] button on the main unit, press the STATUS button on the remote control for more than 3 seconds
Setting Inspection
Voltage Confirmation
A board
Description
Test point
Voltage
SUB1.1V
TP8100
1.10V - 1.22V
SUB 1.5 V
TP8101
1.435V - 1.585V
SUB1.8V
TP8700
1.7V – 1.9V
SUB3.3V
TP5400
3.17V – 3.43V
SUB5V
TP5420
4.80V - 5.25V
USB5V
TP5440
4.94V – 5.40V
FE1.2V
TP5780
1.14V – 1.26V
PNL12V
TP4004 (TP4005)
11.5V – 12.9V

P board
Description
Test point
Voltage*
Voltage**
24V (PANEL)
TP7512/TP7513
<1V
24V ± 1.2V
16V
TP7508/TP7514
<1V
15.7V ± 0.8V
5VS
TP7507/TP7412
5.25V ± 0.25V
5.25V ± 0.25V
PFC
TP7201 and GND
TP7203***
<340V
390V ± 15V

Power LED blinking

When abnormality has occurred the unit, the protection circuit operates and reset to the stand by mode. At this time, the defective block can be identified by number of blinking of the Power LED on the front panel of the unit.
LED BLINKING CODES AND CAUSES 
Blinking times
Contents
Check point
1
BL_SOS
A BOARD
3
IROM SOS
A BOARD
7
SUB3.3V_SENSE_SOS
A BOARD
8
SOS
A BOARD
9
SOUND_SOS
A BOARD
10
FRC_SOS
FR BOARD
12
BE_SOS
A BOARD
13
EMERGENCY
A BOARD

Service Mode Function
MPU controls the functions switching for each IICs through IIC bus in this chassis. The following setting and adjustment can be adjusted by remote control in Service Menu
How to enter SERVICE
While pressing (-/v) button on the TV unit, press 0 on the remote control for 3 times within 2 seconds.
Note:
To exit from Service mode, press the exit button on remote control.
key Command
Press the 3/4 button to change the adjustment values or function.
Press the 1/2 button to step up/down through the functions and adjustments
Press the numerical button VOLUME (+/-) to change of each option item.
Press the OK button after each adjustment has been made to store the required values.
Service Tool Mode
How to access
1. Select [SRV-TOOL] in Service Mode.
2. Press [OK] button on the remote control.
Display of SOS History
SOS History (Number of LED blinking) indication.
From left side; Last SOS, before Last, three occurrence before, 2nd occurrence after shipment, 1st occurrence after shipment.
This indication will be cleared by [Self/check indication and forced to factory shipment setting].
Power ON Time, On/Off
Note: To display TIME/COUNT menu, highlight position, then press MUTE for 3sec.
Time: Cumulative power on time, indicated hour: minute by decimal.
On/Off: Number of On/Off switching by decimal.
Note: This indication will not be cleared by either of the self-checks or any other command.
Exit
Disconnect the AC cord from wall outlet or switch off the power with [Power] button on the main unit.
Hotel Mode
Access command to the Hotel mode setup menu. In order to display the Hotel mode setup menu, please enter the following command (within 2 second).
[TV] : Vol.[Down] + [REMOTE] : AV (3 times)

Chassis Board Layout

Board Name
Function
A-Board


AV Terminal, HDMI, HDMI Switch, USB, USB HUB, Digital Audio Out,
Tuner DVB-T/T2/C, DVB-T/T2/C Dem, SD Card, CI slot, PC, Ethernet,
Wireless LAN, Peaks IC, Speaker out, EEPROM, Flash Memory, DDR SDRAM
FR-Board
Image Processor, SPI Flash
P-Board
Main Input, Power Supply, Key control, Power switch
K-Board
Remote Receiver, Power and Timer LED, C.A.T.S