SAMSUNG LE26B35*** - LE32B35***
SERVICE MODE
General Alignment Instuction
1. Usually, a color LCD-TV needs only slight touch-up adjustment upon installation. Check the basic characteristics such as height, horizontal and vertical sync.
2.Use the specified test equipment or its equivalent.
3.Correct impedance matching is essential.
4.Avoid overload. Excessive signal from a sweep generator might overload the front-end of the TV. When inserting signal markers, do not allow the marker generator to distort test result.
5.Connect the TV only to an AC power source with voltage and frequency as specified on the backcover nameplate.
6.Do not attempt to connect or disconnect any wire while the TV is turned on. Make sure that the power cord is disconnected before replacing any parts.
7.To protect against shock hazard, use an isolation transformer.
Factory Mode Adjustments
Entering Factory Mode
To enter ‘Service Mode’ Press the remote -control keys in this sequence :
- If you do not have Factory remote – control
1. Usually, a color LCD-TV needs only slight touch-up adjustment upon installation. Check the basic characteristics such as height, horizontal and vertical sync.
2.Use the specified test equipment or its equivalent.
3.Correct impedance matching is essential.
4.Avoid overload. Excessive signal from a sweep generator might overload the front-end of the TV. When inserting signal markers, do not allow the marker generator to distort test result.
5.Connect the TV only to an AC power source with voltage and frequency as specified on the backcover nameplate.
6.Do not attempt to connect or disconnect any wire while the TV is turned on. Make sure that the power cord is disconnected before replacing any parts.
7.To protect against shock hazard, use an isolation transformer.
Factory Mode Adjustments
Entering Factory Mode
To enter ‘Service Mode’ Press the remote -control keys in this sequence :
- If you do not have Factory remote – control
Power OFF > INFO > MUTE > Power On
How to Access Service Mode
Using the Customer Remote
1.Turn the power off and set to stand-by mode
2.Press the remote buttons in this order; POWER OFF - INFO - MUTE - POWER ON to turn the set on.
3.The set turns on and enters service mode. This may take approximately 20 seconds.
4.Press the Power button to exit and store data in memory.
- If you fail to enter service mode, repeat steps 1 and 2 above.
Using the Customer Remote
1.Turn the power off and set to stand-by mode
2.Press the remote buttons in this order; POWER OFF - INFO - MUTE - POWER ON to turn the set on.
3.The set turns on and enters service mode. This may take approximately 20 seconds.
4.Press the Power button to exit and store data in memory.
- If you fail to enter service mode, repeat steps 1 and 2 above.
How to enter the hidden factory mode.
a. into the factory mode
b. move the tap to Advanced
c. key input : 0 + 0 + 0 + 0
White Balance - Adjustment
White Ratio (Balance) Adjustment
1.You can adjust the white ratio in factory mode (1:Calibration, 3:White-Balance).
2.Since the adjustment value and the data value vary depending on the input source, you have to adjust these in CVBS, Component 1 and HDMI 1 modes.
3.The optimal values for each mode are configured by default. (Refer to Table 1, 2) It varies with Panel’s size and Specification.
- Equipment : CS-210
- Pattern: MIK K-7256 #92 “Flat W/B Pattern” as standard
- Use other equipment only after comparing the result with
that of the Master equipment.
- Set Aging time : 60min
1.You can adjust the white ratio in factory mode (1:Calibration, 3:White-Balance).
2.Since the adjustment value and the data value vary depending on the input source, you have to adjust these in CVBS, Component 1 and HDMI 1 modes.
3.The optimal values for each mode are configured by default. (Refer to Table 1, 2) It varies with Panel’s size and Specification.
- Equipment : CS-210
- Pattern: MIK K-7256 #92 “Flat W/B Pattern” as standard
- Use other equipment only after comparing the result with
that of the Master equipment.
- Set Aging time : 60min
Calibration and Manual setting for WB
adjustment.
HDMI : Calibration at #24 Chessboard Pattern >
Manual adjustment
COMP: Calibration at #24 Chessboard Pattern >
Manual adjustments
CVBS: Calibration at #24 Chessboard Pattern
> Manual adjustments
- If finishing in HDMI mode, adjustment coordinate is almost same in AV/COMP mode.
- If finishing in HDMI mode, adjustment coordinate is almost same in AV/COMP mode.
