SANYO BLU RAY
|
SANYO LCD-32K30TD
SERVICE MODE
On-screen Service Menu System
Quick operation is needed to enter Service Mode.
How to enter the Service Menu
1. Press and hold the MENU button on Side Controls.
2. Press “1” button on the remote control, and the Service Mode will be displayed.
Quick operation is needed to enter Service Mode.
How to enter the Service Menu
1. Press and hold the MENU button on Side Controls.
2. Press “1” button on the remote control, and the Service Mode will be displayed.
How to select the service item and adjust data:
On-screen Service Menu System
Quick operation is needed to enter Service Mode.
How to enter the Service Menu
1. Press and hold the MENU button on Side Controls.
2. Press “1” button on the remote control, and the Service Mode will be displayed. With the menu, press ▲, ▼, 7 or 8 button to navigate through the options or adjust an option. Press OK button to confirm a selection or enter a sub-menu.
On-screen Service Menu System
Quick operation is needed to enter Service Mode.
How to enter the Service Menu
1. Press and hold the MENU button on Side Controls.
2. Press “1” button on the remote control, and the Service Mode will be displayed. With the menu, press ▲, ▼, 7 or 8 button to navigate through the options or adjust an option. Press OK button to confirm a selection or enter a sub-menu.
To exit service mode
Press MENU button to exit service mode.
Press MENU button to exit service mode.
Setting the Initial data
This adjustment is controlled by the CPU (IC5500) through the IIC Bus Data Line in the chassis, and those adjustment data are memorized the memory IC (IC5750). Therefore, Main board or the memory IC (IC5750) is replaced, these data will be disappeared. Readjust should be made. Initial data is provided in the CPU ROM, when the memory IC (IC5750) is replaced with new one. CPU ROM data is loaded into the memory. Initial data is provided to operating the monitor basically. For operating the monitor quality performance, further adjustment is required following chassis electrical adjustment.
This adjustment is controlled by the CPU (IC5500) through the IIC Bus Data Line in the chassis, and those adjustment data are memorized the memory IC (IC5750). Therefore, Main board or the memory IC (IC5750) is replaced, these data will be disappeared. Readjust should be made. Initial data is provided in the CPU ROM, when the memory IC (IC5750) is replaced with new one. CPU ROM data is loaded into the memory. Initial data is provided to operating the monitor basically. For operating the monitor quality performance, further adjustment is required following chassis electrical adjustment.
1. Receive good quality signal.
2. Enter the Service Mode.
3. ADC ADJUST and W/B ADJUST should be readjusted.
4. Exit the Service Mode.
2. Enter the Service Mode.
3. ADC ADJUST and W/B ADJUST should be readjusted.
4. Exit the Service Mode.
ADC ADJUST
1. Enter the Service Mode.
2. Select "ADC ADJUST" by pressing ▲ or ▼ button, then press OK button to enter ADC ADJUST menu.
1. Enter the Service Mode.
2. Select "ADC ADJUST" by pressing ▲ or ▼ button, then press OK button to enter ADC ADJUST menu.
3. Press ▲ or ▼ button
to select "SOURCE" item, press 7 or 8 button to select RGB, YPbPr(SD)
or
YPbPr(HD).
YPbPr(HD).
RGB
(1). Receive signal from PC input. And set ANSI pattern contrast in PC mode. signal from PC input. And set ANSI pattern contrast in PC mode.
(2). Enter the ADC ADJUST menu. Press the ADC ADJUST menu. Press ▲ or ▼ button to select "SOURCE" item
(3). Press 7 or 8 button to select RGB.
(4). Press ▲ or ▼ button to select AUTO ADC item, then press OK button.
(1). Receive signal from PC input. And set ANSI pattern contrast in PC mode. signal from PC input. And set ANSI pattern contrast in PC mode.
(2). Enter the ADC ADJUST menu. Press the ADC ADJUST menu. Press ▲ or ▼ button to select "SOURCE" item
(3). Press 7 or 8 button to select RGB.
(4). Press ▲ or ▼ button to select AUTO ADC item, then press OK button.
YPbPr (SD)
(1). Receive 100% Colour Bar from
480p and 576p singal in 100% Colour Bar from 480p and 576p singal in YPbPr input.
(2). Enter the ADC ADJUST menu. Press the ADC ADJUST menu. Press ▲ or ▼ button to select "SOURCE" item.
(3). Press 7 or 8 button to select YPbPr (SD).
(4). Press ▲ or ▼ button to select AUTO ADC item, then press OK button.
(2). Enter the ADC ADJUST menu. Press the ADC ADJUST menu. Press ▲ or ▼ button to select "SOURCE" item.
(3). Press 7 or 8 button to select YPbPr (SD).
(4). Press ▲ or ▼ button to select AUTO ADC item, then press OK button.
YPbPr (SD)
(1). Receive 100% Colour Bar from
1080p, 1080i and 720p singal in 100% Colour Bar from 1080p, 1080i and 720p
singal in YPbPr
input.
(2). Enter the ADC ADJUST menu. Press the ADC ADJUST menu. Press ▲ or ▼ button to select "SOURCE" item.
(3). Press 7 or 8 button to select YPbPr (HD).
(4). Press ▲ or ▼ button to select AUTO ADC item, then press OK button.
4. Exit the Service Mode.
Wait for about several seconds until AUTO ADC adjust completed. Then press MENU button to exit.
(2). Enter the ADC ADJUST menu. Press the ADC ADJUST menu. Press ▲ or ▼ button to select "SOURCE" item.
(3). Press 7 or 8 button to select YPbPr (HD).
(4). Press ▲ or ▼ button to select AUTO ADC item, then press OK button.
4. Exit the Service Mode.
Wait for about several seconds until AUTO ADC adjust completed. Then press MENU button to exit.
Note: If you want to adjust any item, please consult
qualified service personnel.
W/B ADJUST
Pattern
White Pattern 100% (in AV mode).
Condition
Picture Mode: STANDARD
Color Temperature: NORMAL
Aging Time: More than 10 minutes
Adjustment
1. Enter the Service Mode.
2. Select "W/B ADJUST" by pressing ▲ or ▼ button, then press OK button to enter W/B ADJUST menu.
Pattern
White Pattern 100% (in AV mode).
Condition
Picture Mode: STANDARD
Color Temperature: NORMAL
Aging Time: More than 10 minutes
Adjustment
1. Enter the Service Mode.
2. Select "W/B ADJUST" by pressing ▲ or ▼ button, then press OK button to enter W/B ADJUST menu.
3. Exit the Service Mode.
After adjustment, confirm white balance again by normal picture.
Note: ● Maybe BASE data for each TV set is different. And the items are for factory setting and Service Centre.
● SOURCE items are for all input source gain. Usually the items can not be adjusted.
● USER items are just for user setting. Usually the items can not be adjusted.
● If you want to adjust any item, please consult qualified service personnel.
After adjustment, confirm white balance again by normal picture.
Note: ● Maybe BASE data for each TV set is different. And the items are for factory setting and Service Centre.
● SOURCE items are for all input source gain. Usually the items can not be adjusted.
● USER items are just for user setting. Usually the items can not be adjusted.
● If you want to adjust any item, please consult qualified service personnel.
