Wednesday, March 20, 2013

BENQ W1070 - W 1080 ST LAMP REPLACEMENT - LAMP RESET

                                Replacing the lamp


• To reduce the risk of electrical shock, always turn the projector off and disconnect the power cable before changing the lamp.
• To reduce the risk of severe burns, allow the projector to cool for at least 45 minutes before replacing the
lamp.
• To reduce the risk of injuries to fingers and damage to internal components, use caution when removing lamp glass that has shattered into sharp pieces.
• To reduce the risk of injuries to fingers and/or compromising image quality by touching the lens, do not touch the empty lamp compartment when the lamp is removed.
• This lamp contains mercury. Consult your local hazardous waste regulations to dispose of this lamp in a
proper manner. Status Message Install a new lamp for optimal performance. If the projector is normally run with Economics elected , you may continue to operate the projector until the next hour lamp warning appears. Press MODE/ENTER to dismiss the message. It is strongly recommended that you replace the lamp at this stage. The lamp is a consumable item. The lamp brightness diminishes with use. This is normal lamp behavior. You can replace the lamp whenever you notice that the brightness level has significantly diminished. Press MODE/ENTER to dismiss the message. The lamp MUST be replaced before the projector will operate normally. Press MODE/ENTER to dismiss the message.

1. Turn the power off and disconnect the projector from the power outlet. If the lamp is hot, avoid
burns by waiting for approximately 45 minutes until the lamp has cooled.

2. Loosen the screw that secures the lamp cover on the side of the projector until the lamp cover loosens.


3. Remove the lamp cover from the projector.
• Do not turn the power on with the lamp cover removed.
• Do not insert your fingers between the lamp and the projector. The sharp edges inside the projector may cause injuries.



4. Loosen the screw that secures the lamp.
5. Lift the handle so that it stands up.



6. Use the handle to slowly pull the lamp out of the projector.
• Pulling it too quickly may cause the lamp to break and scatter broken glass in the projector.
• Do not place the lamp in locations where water might splash on it, children can reach it, or near flammable materials.
• Do not insert your hands into the projector after the lamp is  removed. If you touch the optical components inside, it could cause color unevenness and distortion of the projected images.

7. As shown in the figure, lower the new lamp.



8. Tighten the screw that secures the lamp.
9. Ensure the handle is fully laid flat and locked in place.
• Loose screw may cause a bad connection, which could result in  Malfunction.
• Do not over tighten the screw.


10. Replace the lamp cover on the projector.


11. Tighten the screw that secures the lamp cover.
• Loose screw may cause a bad connection, which could result in malfunction.
• Do not over tighten the screw.


12. Connect the power and restart the projector.

               Resetting the lamp timer

Do not reset the lamp timer if the lamp has not been replaced as this could cause damage.
13. After the start-up logo, press MENU/EXIT and then press / until the System Setup :
Advanced menu is highlighted.
14. Press to highlight Lamp Settings and press MODE/ENTER. The Lamp Settings page displays.
15. Highlight Reset Lamp Timer and press MODE/ENTER. A warning message displays asking if you
want to reset the lamp timer. Highlight Reset and press MODE/ENTER. The lamp time will be
reset to "0".

                                   

BENQ MS612 ST LAMP REPLACEMENT - LAMP RESET



                                                          Replacing the lamp

• To reduce the risk of electrical shock, always turn the projector off and disconnect the power cord before
changing the lamp.
• To reduce the risk of severe burns, allow the projector to cool for at least 45 minutes before replacing the
lamp.
• To reduce the risk of injuries to fingers and damageto internal components, use caution when removing
lamp glass that has shattered into sharp pieces.
• To reduce the risk of injuries to fingers and/or compromising image quality by touching the lens, do not
touch the empty lamp compartment when the lamp is removed.
• This lamp contains mercury. Consult your local hazardous waste regulations to dispose of this lamp in a
proper manner.
• To assure optimal performance from the projector,it is recommended that you purchase a qualified
projector lamp for lamp replacement.
• If lamp replacement is performed while the projector is suspended upside-down from the ceiling, make
sure that no one is underneath the lamp socket to avoid any possible injury or damage to the human eyes
caused by fractured lamp.

1. Turn the power off and disconnect the projector from the power outlet. If the lamp is hot, avoid burns by waiting for approximately 45 minutes until the lamp has cooled.

2. Loosen the screw(s) that secures the lamp cover on the side of the projector until the lamp cover
loosens


3. Remove the lamp cover from the projector.



• Do not turn the power on with the lamp cover removed.

• Do not insert your fingers between the lamp and the projector.

The sharp edges inside the projector may cause injuries.

4. Disconnect the lamp connector from the projector as illustrated.

5. Loosen the screw that secures the lamp.

6. Lift the handle so that it stands up




7. Use the handle to slowly pull the lamp out of the projector.

• Pulling it too quickly may cause the lamp to break and scatter broken glass in the projector.

• Do not place the lamp in locationswhere water might splash on it, children can reach it, or near flammable materials.

• Do not insert your hands into the projector after the lamp is removed. If you touch the optical components inside, it could cause color unevenness and distortion of the projected images.



8. As shown in the figure, lower the new lamp



9. Tighten the screw that secures the lamp.

10. Ensure the handle is fully laid flat and locked in place.

11. Reconnect the lamp connector.

• Loose screw may cause a bad connection, which could result in malfunction.

• Do not over tighten the screw



12. Replace the lamp cover on the projector.



13. Tighten the screw(s) that secures the lamp cover.

• Loose screw may cause a bad connection, which could result in malfunction.

• Do not over tighten the screw.



14. Connect the power and restart the projector. Do not turn the power on with the lamp cover removed.

                                                      Resetting the lamp timer


15. After the start up logo, open the On-Screen Display (OSD) menu. Go to the SYSTEM SETUP: Advanced> Lamp Settings menu. Press MODE/ENTER. The Lamp Settings page displays. Highlight Reset Lamp Timer. A warning message is displayed asking if you want to reset the lamp timer. Highlight Reset and press MODE/ENTER. The lamp time will be reset to “0”. Do not reset if the lamp is not new or replaced as this could cause damage.
                                       

                          

    

BENQ MX 613 ST LAMP REPLACEMENT - LAMP RESET



                                                          Replacing the lamp

• To reduce the risk of electrical shock, always turn the projector off and disconnect the power cord before
changing the lamp.
• To reduce the risk of severe burns, allow the projector to cool for at least 45 minutes before replacing the
lamp.
• To reduce the risk of injuries to fingers and damageto internal components, use caution when removing
lamp glass that has shattered into sharp pieces.
• To reduce the risk of injuries to fingers and/or compromising image quality by touching the lens, do not
touch the empty lamp compartment when the lamp is removed.
• This lamp contains mercury. Consult your local hazardous waste regulations to dispose of this lamp in a
proper manner.
• To assure optimal performance from the projector,it is recommended that you purchase a qualified
projector lamp for lamp replacement.
• If lamp replacement is performed while the projector is suspended upside-down from the ceiling, make
sure that no one is underneath the lamp socket to avoid any possible injury or damage to the human eyes
caused by fractured lamp.

1. Turn the power off and disconnect the projector from the power outlet. If the lamp is hot, avoid burns by waiting for approximately 45 minutes until the lamp has cooled.

2. Loosen the screw(s) that secures the lamp cover on the side of the projector until the lamp cover
loosens


3. Remove the lamp cover from the projector.



• Do not turn the power on with the lamp cover removed.

• Do not insert your fingers between the lamp and the projector. The sharp edges inside the projector may cause injuries.

4. Disconnect the lamp connector from the projector as illustrated.

5. Loosen the screw that secures the lamp.

6. Lift the handle so that it stands up




7. Use the handle to slowly pull the lamp out of the projector.

• Pulling it too quickly may cause the lamp to break and scatter broken glass in the projector.

• Do not place the lamp in locationswhere water might splash on it, children can reach it, or near flammable materials.

• Do not insert your hands into the projector after the lamp is removed. If you touch the optical components inside, it could cause color unevenness and distortion of the projected images.



8. As shown in the figure, lower the new lamp



9. Tighten the screw that secures the lamp.

10. Ensure the handle is fully laid flat and locked in place.

11. Reconnect the lamp connector.

• Loose screw may cause a bad connection, which could result in malfunction.

• Do not over tighten the screw



12. Replace the lamp cover on the projector.



13. Tighten the screw(s) that secures the lamp cover.

• Loose screw may cause a bad connection, which could result in malfunction.

• Do not over tighten the screw.



14. Connect the power and restart the projector. Do not turn the power on with the lamp cover removed.

                                                      Resetting the lamp timer


15. After the start up logo, open the On-Screen Display (OSD) menu. Go to the SYSTEM SETUP: Advanced> Lamp Settings menu. Press MODE/ENTER. The Lamp Settings page displays. Highlight Reset Lamp Timer. A warning message is displayed asking if you want to reset the lamp timer. Highlight Reset and press MODE/ENTER. The lamp time will be reset to “0”. Do not reset if the lamp is not new or replaced as this could cause damage.
                                                         
                

HOW TO REPLACE LAMP BENQ MX 722 - PROJECTOR - Projector Repair and service - Manual Service


                                               

                                                         Replacing the lamp

• To reduce the risk of electrical shock, always turn the projector off and disconnect the power cord before
changing the lamp.
• To reduce the risk of severe burns, allow the projector to cool for at least 45 minutes before replacing the
lamp.
• To reduce the risk of injuries to fingers and damageto internal components, use caution when removing
lamp glass that has shattered into sharp pieces.
• To reduce the risk of injuries to fingers and/or compromising image quality by touching the lens, do not
touch the empty lamp compartment when the lamp is removed.
• This lamp contains mercury. Consult your local hazardous waste regulations to dispose of this lamp in a
proper manner.
• To assure optimal performance from the projector,it is recommended that you purchase a qualified
projector lamp for lamp replacement.
• If lamp replacement is performed while the projector is suspended upside-down from the ceiling, make
sure that no one is underneath the lamp socket to avoid any possible injury or damage to the human eyes
caused by fractured lamp.
1. Turn the power off and disconnect the projector from the power outlet. If the lamp is hot, avoid burns by waiting for approximately 45 minutes until the lamp has cooled.
2. Loosen the screw(s) that secures the lamp cover on the side of the projector until the lamp cover
loosens

Remove the lamp cover from the projector.


 * Do not turn the power on with the lamp cover removed.
 * Do not insert your fingers between the lamp and the projector.
The sharp edges inside the projector may cause injuries.
 Disconnect the lamp connector from the projector as illustrated.
 Loosen the screw that secures the lamp.
 Lift the handle so that it stands up


 Use the handle to slowly pull the lamp out of the projector.
• Pulling it too quickly may cause the lamp to break and scatter broken glass in the projector.
• Do not place the lamp in locations where water might splash on it, children can reach it, or near flammable materials.
• Do not insert your hands into the projector after the lamp is removed. If you touch the optical components inside, it could cause color unevenness and distortion of the projected images.
As shown in the figure, lower the new lamp
Tighten the screw that secures the lamp.
Ensure the handle is fully laid flat and locked in place.
Reconnect the lamp connector.
• Loose screw may cause a bad connection, which could result in malfunction.
• Do not over tighten the screw

 Replace the lamp cover on the projector.
 Tighten the screw(s) that secures the lamp cover.
• Loose screw may cause a bad connection, which could result in malfunction.
• Do not over tighten the screw.
Connect the power and restart the projector. Do not turn the power on with the lamp cover removed.
                                                      Resetting the lamp timer
15. After the start up logo, open the On-Screen Display (OSD) menu. Go to the SYSTEM SETUP: Advanced> Lamp Settings menu. Press MODE/ENTER. The Lamp Settings page displays. Highlight Reset Lamp Timer. A warning message is displayed asking if you want to reset the lamp timer. Highlight Reset and press MODE/ENTER. The lamp time will be reset to “0”. Do not reset if the lamp is not new or replaced as this could cause damage.
            

Friday, March 15, 2013

BIG BUTTON REMOTE CONTROL CODE



                                               
                                               PROGRAMMING A DEVICE
  The DIRECTV Big Button Remote comes preprogrammed to operate a DTV Receiver or DVR. To
control devices other than default brands, follow these steps; otherwise, skip this section. Before proceeding, find the codes for the devices you want to program in Manufacturer's Codes and write  them down or highlight them. (See “Manufacturer’s Codes” on page 13.) NOTE: To program a TV/DVD, TV/VCR/DVD, or TV/ VCR Combo, use the AUX 1 or AUX 2 key.
1. Turn on the device (for example, TV) and, if needed, load media (for example, DVD).
2. On the remote, press and release the appropriate mode key for the device you want to program (that is, 
DIRECTV, TV, AUX 1, or AUX 2).
3. Press and hold the mode key until the green LED flashes twice. Release the key.
4. Enter the first five-digit code for your device. The LED blinks once as each digit is entered. If the code is correct, the LED blinks twice.
NOTE: If the LED does not blink twice, repeat steps 2 to 5 and try entering the code again.
5. Aim the remote at the device and press POWER (or PLAY, if it does not have a POWER key). The device should turn off. If it does not, repeat steps 2 to 6, trying each code for your brand until you find one that works. If you cannot find a code that works,
see Searching for Your Code.
6. Repeat steps 1 to 5 for each device. For future reference, write down each working device code in a safe place.
MANUFACTURER  CODE 
Setup Codes for TVs
A-Mark 10003
Abex 10032
Admiral 1093, 10463
Advent 10761, 10783, 10815,10817, 10842
Adventura 10046
Aiko 1092
Akai 10030, 10060, 10672,10702, 10812
Alaron 10179
Albatron 10700, 10843
Ambassador 10177
America Action 10180
Ampro 10751
Anam 10180
Anam National 10055
AOC 10003, 10019, 10030,10052, 10185
Apex Digital 10156, 10748, 10765,10767, 10879
Archer 10003
Audiovox 10003, 1092, 10180, 10451,10623, 10802, 10875, 11284
Aventura 10171
Belcor 10019
Bell & Howell 10016, 10154
BenQ 11032, 11315
Boxlight 10893
Bradford 10180
Brockwood 10019
Broksonic 10003, 10180, 10236, 10463
Cadia 11283
Candle 10030, 10046, 10056, 10186
Carnivale 10030
Carver 10054
CCE 10217
Celebrity 10000
Celera 10765
Changhong 10765
Citizen 10030, 10039, 10046,10056, 10060, 1092, 10186,
            10280
Clairtone 10185
Clarion 10180
Commercial Solutions 10047, 11447
Concerto 10056
Contec 10157, 10180, 10185
Craig 10180
Crosley 10054
Crown 10039, 10180
Curtis Mathes 10016, 10030, 10039,10047, 10054, 10056,
               10060, 1093, 1145, 10154,10166, 10451, 10466,
              10702, 11147, 11347
CXC 10180
Daewoo 10019, 10039, 1092, 10451,
10623, 10661, 10672, 11661
Daytron 10019
Dell 11080, 11178, 11264, 11454
Denon 1145, 10511
Denstar 10628
Dumont 10017, 10019
Durabrand 10003, 10171, 10178,10180, 10463, 11034
Dwin 1093, 10720, 10774
Electroband 10000, 10185
Electrograph 11755
Electrohome 10381
Emerson 10019, 10038, 10039,10154, 10171, 10177,
           10178, 10179, 10180,10185, 10236, 10280,
             10282, 10451, 10463, 10623
Envision 10030, 10813
Epson 10833, 10840
ESA 10171, 10812
Fisher 10154, 10159
Fujitsu 10179, 10186, 10683,10809, 10853
Funai 10171, 10179, 10180
Futuretech 10180
Gateway    11755, 11756

GE  10021, 10027, 10047,10051, 10055, 1135, 10178,
           10282, 10451, 11347, 11447
Gibralter 10017, 10019, 10030
Go Video 10886
GoldStar 10001, 10019, 10030,10032, 10178
Goodmans 10360
Grundig 10683
Grunpy 10179, 10180
Haier 10768, 11034
Hallmark 10178
Hannspree 11348, 11351, 11352
Harley Davidson 10179
Harman/Kardon 10054
Harvard 10180
Havermy 1093
Helios 10865
Hello Kitty 10451
Hewlett Packard 11502
Hisense 10748
Hitachi 10016, 10032, 10038,10056, 1145, 10151, 11145
HP 11502
Hyundai 10849
Infinity 10054
Inteq 10017
Janeil 10046
JBL 10054
JCB 10000
Jensen 10761, 10815, 10817
JVC 10053, 10731, 11253, 11352
Kaypani 10052
KEC 10180
Kenwood 10019, 10030
KLH 10765, 10767
Kloss 10024, 10046
Konka 10628, 10632, 10638,10703, 10707
KTV 10030, 10039, 10180,10185, 10217, 10280
LG 10178, 10442, 10700,10856, 11178, 11265

Loewe 1136
Logik 10016
Luxman 10056
LXI 10047, 10054, 10154,10156, 10178
Magnavox 10020, 10024, 10030,10054, 1096, 10179, 10186,
                   10187, 10386, 10706,10802, 11254, 11454
Majestic 10016
Marantz 10030, 10054, 10704,10855, 11154, 11454
Matsushita 10250, 10650
Maxent 11755
Megapower 10700
Megatron 10003, 1145, 10178
MEI 10185
Memorex 10016, 1150, 10154, 10178,10179, 10463
MGA 10019, 10030, 1150, 10178
Midland 10017, 10032, 10039,10047, 10051, 1135
Minutz 10021
Mitsubishi 10019, 1093, 1150, 10178,10836, 10868, 11250
Monivision 10700, 10843
Motorola 10055, 1093
MTC 10019, 10030, 10056,10060, 10185
Multitech 10180, 10217
NAD 10156, 10178, 10866
NEC 10019, 10030, 10056, 10497, 10882, 11704
NetTV 11755
Nikko 10030, 1092, 10178
Norcent 10748, 10824
Noshi 10018
NTC 1092
Olevia 11331
Onwa 10180
Optimus 10154, 10166, 10250, 10650
Optoma 10887, 11348
Optonica 1093, 10165
Orion 10179, 10236, 10463, 11463

Panasonic 10051, 10055, 10250,10650, 11410

Penney 10003, 10018, 10019, 10021, 10027, 10030,
  10032, 10039, 10047,10051, 10060, 1135, 10156,
   10178, 11347

Philco 10019, 10020, 10030, 10054, 1096
Philips 10054, 10690, 11154, 11454
Pilot 10019, 10030, 10039
Pioneer 10038, 10166, 10679, 10866
Polaroid 10765, 10865, 11276,11314, 11316, 11326,
              11327, 11328
Portland 10019, 10039, 1092
Prima 10761, 10783, 10815, 10817
Princeton 10700, 10717
Prism 10051
Proscan 10047, 10466, 11347, 11447
Proton 10003, 10052, 10178, 10466
Pulsar 10017, 10019
Quasar 10051, 10055, 10165,10250, 10650
RadioShack 10019, 10030, 10032,10039, 10047, 10056,
                    10154, 10165, 10178, 10180

RCA 10018, 10019, 10038,10047, 1090, 1135, 10679,
                11047, 11147, 11247,11347, 11447, 11547

Realistic 10019, 10030, 10032,10039, 10056, 10154,
               10165, 10178, 10180
Rhapsody 10185
Runco 10017, 10030, 10497, 10603
Sampo 10030, 10032, 10039,10052, 11755
Samsung 10019, 10030, 10032,10056, 10060, 10178,10217, 10587, 10702,
               10766, 10812, 10814,11060, 11312
Samsux 10039
Sansui 10463
Sanyo 10088, 1146, 10154, 10159,
10799, 10893
Sceptre 11360
Scimitsu 10019
Scotch 10178
Scott 10019, 10178, 10179,
10180, 10236
Sears 10047, 10054, 10056, 1146, 10154, 10156, 10159,
            10171, 10178, 10179
Seleco 11351
Sharp 10039, 1093, 10157, 10165,10386, 10491, 10688,
            10689, 10851

Sheng Chia 1093
Shogun 10019
Signature 10016
Simpson 10186, 10187
Sole 10813
Sony 10000, 10080, 1111, 10834,11100
Soundesign 10178, 10179, 10180, 10186
Spectricon 10003
Squareview 10171
SSS 10019, 10180
Starlite 10180
Studio Experience 10843
Superscan 1093, 10864
Supre-Macy 10046
Supreme 10000
SVA 10587, 10748, 10768, 10865, 10870, 10871, 10872
Sylvania 10020, 10030, 10054, 1096,10171, 10381
Symphonic 10171, 10180
Syntax 11331
Tandy 1093
Tatung 10003, 10055, 11285, 11756
Technics 10051, 10250
Technol Ace 10179
Techview 10847
Techwood 10003, 10051, 10056
Teknika 10016, 10019, 10039, 10054, 10056, 10060, 1092,
                1150, 10179, 10180, 10186

Telefunken 10056, 10702

TMK 10056, 10177, 10178
TNCi 10017
Toshiba 10060, 10154, 10156,10650, 10832, 10845,
11156, 11256, 11265,11343, 11356, 11360,11656, 11704

Tosonic 10185
Totevision 10039
Trical 10157
TVS 10463
Universal 10027
Vector Research 10030
Victor 10053
Vidikron 10054
Vidtech 10019, 10178
Viewsonic 10857, 10864, 10885,11330, 11342, 11755
Viking 10046
Vizio 10864, 10885, 11756
Wards 10016, 10019, 10020,10021, 10027, 10030,10054, 10056, 10080, 1096,
           1111, 10165, 10178, 10179,10866, 11156
Waycon 10156
Westinghouse 10000, 10451, 10885,10889, 11282
White Westinghouse 10463, 10623
Yamaha 10019, 10030, 10769,
10833, 10839
Zenith 10016, 10017, 1092, 10178,10463, 11145, 11265
Zonda 10003


Setup Codes for DVD Players

Aiwa 20641
Akai 20695, 20770, 21089
Alco 20790
Allegro 20869
Amphion Media Works 20872
AMW 20872
Apex Digital 20672, 20717, 20755, 20794,20796, 20797, 21004, 21020,21056, 21061, 21100
Aspire Digital 21168, 21407
Audiovox 20790, 21041, 21072
Axion 21072
B & K 20655, 20662
Blaupunkt 20717
Blue Parade 20571
Broksonic 20695
California Audio Labs 20490
Cinea 20831
CineVision 20833, 20869, 20876
Citizen 21277
Coby 20778, 20852, 21086, 21107,21177, 21351
Craig 20831
Curtis Mathes 21087
CyberHome 20816, 20874, 21023, 21024

Daewoo 20705, 20784, 20833, 20869,21169, 21172, 21234, 21242
Daytek 20872
Denon 20490, 20634
Desay 21407
Disney 20675, 21270
Dual 21068, 21085
Durabrand 21127
DVD2000 20521
Emerson 20591, 20675, 20821
Enterprise 20591
Fisher 20670
Funai 20675, 21334
Gateway 21073, 21077, 21158
GE 20522, 20717, 20815
Go Video 20715, 20741, 20744, 20783,20833, 20869, 21044, 21075,21099, 21158, 21304, 21730
Go Vision 21072
GoldStar 20741
GPX 20699, 20769
Gradiente 20490
Greenhill 20717
Grundig 20539
Harman/Kardon 20582, 20702
Hitachi 20573, 20664
Hiteker 20672
iLo 21348
Initial 20717
Integra 20571, 20627
Jaton 21078
JBL 20702
JSI 21423
JVC 20558, 20623, 20867, 21164
jWin 21049, 21051
Kawasaki 20790
Kenwood 20490, 20534
KLH 20717, 20790, 21020, 21149
Konka 20711
Koss 20651, 21423
Landel 20826
Lasonic 20798, 21173

Lecson 21533
Lenoxx 21127
LG 20591, 20741, 20801, 20869
LiteOn 21058, 21158, 21416, 21440
Loewe 20511
Magnavox 20503, 20539, 20646, 20675,20821
Malata 20782, 21159
Marantz 20539
McIntosh 21533
Memorex 20695, 20831, 21270
Microsoft 20522
Mintek 20717, 20839
Mitsubishi 20521, 21521
Momitsu 21082
NAD 20591, 20692, 20741
NEC 20785
Nesa 20717
Next Base 20826
NexxTech 21402
Norcent 20872, 21003, 21107, 21265
Onkyo 20503, 20627, 20792
Oritron 20651
Panasonic 20490, 20503, 20703, 21362,21462, 21490, 21762
Philips 20503, 20539, 20646, 20675,21267, 21354
PianoDisc 21024
Pioneer 20525, 20571, 20631
Polaroid 21020, 21061, 21086
Polk Audio 20539
Portland 20770
Presidian 20675
Proceed 20672
Proscan 20522
ProVision 20778
Qwestar 20651
RCA 20522, 20571, 20717, 20790,
20822
Rio 20869
RJTech 21360
Rotel 20623
Rowa 20823

Sampo 20698, 20752
Samsung 20490, 20573, 20744, 20820,21044, 21075
Sansui 20695
Sanyo 20670, 20695, 20873
Sensory Science 21158
Sharp 20630, 20675, 20752, 21256
Sharper Image 21117
Sherwood 20633, 20770, 21043, 21077
Shinsonic 20533, 20839
Sonic Blue 20869, 21099
Sony 20533, 20864, 21033, 21431,21533
Sungale 21074
Superscan 20821
SVA 20860, 21105
Sylvania 20675, 20821
Symphonic 20675
Teac 20790, 20809
Technics 20490, 20703
Technosonic 20730
Techwood 20692
Theta Digital 20571
Toshiba 20503, 20695, 21154
Tredex 20800, 20803, 20804
Urban Concepts 20503
US Logic 20839
Venturer 20790
Vizio 21064, 21226
Xbox 20522
Yamaha 20490, 20539, 20545
Yamakawa 20872
Zenith 20503, 20591, 20741, 20869
Zoece 21265

Setup Codes for Audio Amplifiers/Tuners

Sampo 20698, 20752
Samsung 20490, 20573, 20744, 20820,21044, 21075
Sansui 20695
Sanyo 20670, 20695, 20873
Sensory Science 21158
Sharp 20630, 20675, 20752, 21256
Sharper Image 21117
Sherwood 20633, 20770, 21043, 21077
Shinsonic 20533, 20839
Sonic Blue 20869, 21099
Sony 20533, 20864, 21033, 21431,21533
Sungale 21074
Superscan 20821
SVA 20860, 21105
Sylvania 20675, 20821
Symphonic 20675
Teac 20790, 20809
Technics 20490, 20703
Technosonic 20730
Techwood 20692
Theta Digital 20571
Toshiba 20503, 20695, 21154
Tredex 20800, 20803, 20804
Urban Concepts 20503
US Logic 20839
Venturer 20790
Vizio 21064, 21226
Xbox 20522
Yamaha 20490, 20539, 20545
Yamakawa 20872
Zenith 20503, 20591, 20741, 20869
Zoece 21265
ADC 30531
Adcom 30616
Aiwa 30121, 30189, 31243, 31388,31405, 31641
Akai 30224, 31255, 31512
Alco 31390
AMC 31077

Amphion Media Works 31563, 31615
AMW 31563, 31615
Anam 31074, 31609
Apex Digital 31257, 31430, 31774
Arcam 31189
Audiotronic 31189
Audiovox 31390, 31627
B & K 30701, 30820, 30840
BK 30702
Bose 30639, 31229, 31253, 31933
Brix 31602
Cambridge Soundworks 31370
Capetronic 30531
Carver 30008, 30121, 30189, 30360,31189, 31289
Classic 31352
Coby 31389
Criterion 31420
Daewoo 31250
Delphi 31414
Denon 30121, 30273, 30771, 31142,31360
Emerson 30424
Fisher 30219, 30360, 31801
Garrard 30424
Gateway 31517, 31567
Go Video 31532
Harman/Kardon 30110, 30189, 30891, 31289,31304, 31306
Hitachi 31273, 31801
Initial 31426
Inkel 30062
Integra 30135, 31298, 31320
JBL 30110, 31306
JVC 30074, 31058, 31374, 31495,31811
Kenwood 30077, 30186, 31313, 31569,31570
KLH 31390, 31412, 31428
Koss 30424, 31366, 31497
Lasonic 31798
Lenoxx 31437
Lexicon 31076

LG 31293
Linn 30189
Liquid Video 31497
Magnavox 30128, 30189, 30531, 31189,31269, 31514
Marantz 30039, 30128, 30189, 31189,
31269, 31289
McIntosh 31289
MCS 30039, 30346
Micromega 31189
Mitsubishi 31393
Myryad 31189
Nakamichi 30347, 31313
NEC 30235
Norcent 31389
Nova 31389
Onkyo 30135, 30380, 30842, 31298,31320, 31531
Optimus 30177, 30186, 30219, 30531,30670, 31023, 31074
Oritron 31366, 31497
Panasonic 30039, 30309, 31288, 31308,31316, 31350, 31363, 31518,31548, 31633, 31763, 31764
Philips 30189, 31189, 31266, 31269
Pioneer 30014, 30150, 30531, 30630,31023, 31384
Polaroid 31508
Polk Audio 30189, 31289, 31414
Proscan 31254
Quasar 30039
RCA 30346, 30360, 30530, 30531,31023, 31074, 31254, 31390,31511, 31609
Realistic 30163
Regent 31437
Rio 31869
Saba 31519
Samsung 31295, 31304, 31500
Sansui 30189, 30346, 31189
Sanyo 30219, 31469, 31801
Scott 30163, 30322

Sharp 30186
Sharper Image 31556
Sherwood 30062, 31077, 31423, 31517,31567, 31653
Shinsonic 31426
Sirius 31602, 31627, 31811
Sonic Blue 31532, 31869
Sony 30168, 31058, 31258, 31406,31441, 31558, 31622, 31658,31758, 31759, 31858
Soundesign 30670
Stereophonics 31023
Sunfire 31313
Teac 30163, 31074, 31267, 31390,.31528
Technics 30039, 30208, 30309, 31308,.31518, 31633
Thorens 31189
Toshiba 30135
Venturer 31390
Victor 30074
Wards 30014, 30189
XM 31406, 31414
Yamaha 30176, 30186, 31176, 31276,,31331, 31375
Zenith 31293

Setup Codes for Audio Amplifiers

Adcom 30577, 31100
AudioSource 30011
Bose 30674
Carver 30892
Durabrand 31561
Elan 30647
GE 30078
Harman/Kardon 30892
JVC 30331
Kenwood 30356
Left Coast 30892
Lenoxx 31561
Luxman 30165
Marantz 30321, 30892
McIntosh 30251
Nakamichi 30321

NEC 30264
Optimus 30395, 30823
Parasound 30246
Philips 30892
Pioneer 30823
Polk Audio 30892
RCA 30823
Realistic 30395
Sansui 30321
Shure 30264
Sony 30689, 30815, 31126
Soundesign 30078, 30211
Victor 30331
Wards 30078, 30211
Yamaha 30133, 30143, 30354, 30504

Setup Codes for DIRECTV Receivers

DIRECTV all models ……………………00001, 00002

Hughes Network Systems
(most models)………………………………00749

Hughes Network Systems
models GAEB0, GAEB0A,
GCB0, GCEB0A, HBH-SA,
HAH-SA……………………………………01749

GE models GRD33G2A and
GRD33G3A, GRD122GW………………….00566

Philips models DSX5500
and DSX5400……………………………….00099

Proscan models PRD8630A
and PRD8650B…………………………….00566

RCA models DRD102RW,
DRD203RW, DRD301RA,
DRD302RA, DRD303RA,
DRD403RA, DRD703RA,
DRD502RB, DRD 503RB,
DRD505RB, DRD515RB,
DRD523RB, and
DRD705RB……………………………….00566

DRD440RE, DRD460RE,
DRD480RE,DRD430RG,
DRD431RG, DRD450RG,
DRD451RG,
DRD485RG,DRD486RG,
DRD430RGA,
DRD450RGA,
DRD485RGA, DRD435RH,
DRD455RH, and
DRD486RH………………………………………. 00392

Samsung model SIR-S60W 01109
Samsung models SIR-S70,
SIR-S75, SIR-S300W, and
SIR-S310W………………………………………… 01108

Sony models (All models
except TiVo and Ultimate
TV)………………………………………………… 01639



Setup Codes for DIRECTV HD Receivers

DIRECTV all models ……………………00001, 00002

Hitachi model 61HDX98B 00819
HNS models HIRD-E8,
HTL-HD……………………………….01750

LG model LSS-3200A,
HTL-HD……………………………….01750

Mitsubishi model SR-HD5………….. 01749, 00749