Tuesday, December 24, 2013

PHILIPS 32PFL3606 - 40PFL3606 - SERVICE MODE & LED BLINKING CODES - LCD TV


SERVICE MODE
Service Alignment Mode (SAM)
Press the following key sequence on the remote control transmitter: “062596” directly followed by the INFO[i+] /OK button. Do not allow the display to time out between entries  while keying the sequence.
After entering SAM, the following items are displayed, with “SAM” in the upper right corner of the screen to indicate that the television is in Service Alignment Mode.
How to Navigate.
In the SAM menu, select menu items with the UP/DOWN keys on the remote control transmitter. The selected item will be indicated. When not all menu items fit on the screen, 
use the UP/DOWN keys to display the next / previous menu items.
With the LEFT/RIGHT keys, it is possible to:
Activate the selected menu item.
Change the value of the selected menu item.
Activate the selected sub menu.
When you press the MENU button twice while in top level SAM, the set will switch to the normal user menu (with the SAM mode still active in the background). To return to the SAM menu press the MENU button.
The “INFO[i+]/OK” key from the user remote will toggle the OSD “on/off” with “SAM” OSD remaining always “on”.
Press the following key sequence on the remote control transmitter: “062596” directly followed by the MENUbutton to switch to SDM (do not allow the display to time out between entries while keying the sequence)
How to Store SAM Settings
To store the settings changed in SAM mode (except the OPTIONS and RGB ALIGN settings), leave the top level SAM menu by using the POWER button on the remote control transmitter or the television set. The mentioned exceptions must be stored separately via the STORE button.
How to Exit
Switch the set to STANDBY by pressing the mains button on the remote control transmitter or the television set, or by keying-in the “00” sequence on a standard RC-transmitter.
Note: When the TV is switched “off” by a power interrupt while in SAM, the TV will show up in “normal operation mode” as soon as the power is supplied again. The error buffer will 
not be cleared.
In case the set is in Factory mode by accident (with “F” displayed on screen), pressing and holding “VOL-“ button for 5 seconds and then followed by pressing and holding the “CH-” button for another 5 seconds should exit the Factory mode.
Error Codes
Error codes are required to indicate failures in the TV set. In principle a unique error code is available for every:
Activated (SW) protection.
Failing I2C device.
General I2C error.
The last five errors, stored in the NVM, are shown in the Service menu’s. This is called the error buffer.  The error code buffer contains all errors detected since the last time the buffer was erased. The buffer is written from left to right. When an error occurs that is not yet in the error code buffer, it is displayed at the left side and all other errors shift one position to the right.  An error will be added to the buffer if this error differs from any error in the buffer. The last found error is displayed on the left.  An error with a designated error code everleads to a deadlock situation. It must always be diagnosable (e.g. error buffer via OSD or blinking LED or via ComPair).  In case a failure identified by an error code automatically results in other error codes (cause and effect), only the error code of the MAIN failure is displayed.
How to Read the Error Buffer
On screen via the SAM/SDM/CSM (if you have a picture). 
Example:
> ERROR: 0 0 0 0 0: No errors detected
> ERROR: 6 0 0 0 0: Error code 6 is the last and only detected error
> ERROR: 9 6 0 0 0: Error code 6 was detected first and error code 9 is the last detected (newest) error
> Via the blinking LED procedure (when you have no picture)
How to Clear the Error Buffer.
The error code buffer is cleared in the following cases:
> By using the CLEAR command in the SAM menu:
> By using the following key sequence on the remote control transmitter: “062599” directly followed by the OKbutton.
>If the contents of the error buffer have not changed for 50 hours, the error buffer resets automatically.
Note: If you exit SAM by disconnecting the mains from the television set, the error buffer is not reset.

The Blinking LED Procedure
The software is capable of identifying different kinds of errors. Because it is possible that more than one error can occur over time, an error buffer is available, which is capable of storing the last five errors that occurred. This is useful if the OSD is not working properly.
Errors can also be displayed by the blinking LED procedure. The method is to repeatedly let the front LED pulse with as many pulses as the error code number, followed by a period of 
1.5 seconds in which the LED is “off”. Then this sequence is repeated.
Example (1): error code 4 will result in four times the sequence LED “on” for 0.25 seconds / LED “off” for 0.25 seconds. After this sequence, the LED will be “off” for 1.5 seconds. Any RC 
command terminates the sequence. Error code LED blinking is in red color.
Example (2): the content of the error buffer is “129600” After entering SDM, the following occurs: 
1 long blink of 5 seconds to start the sequence,
12 short blinks followed by a pause of 1.5 seconds,
9 short blinks followed by a pause of 1.5 seconds,
6 short blinks followed by a pause of 1.5 seconds,
1 long blink of 1.5 seconds to finish the sequence,
The sequence starts again with 12 short blinks.

Additionally, the entire error buffer is displayed when Service Mode “SDM” is entered.

Saturday, December 21, 2013

VAIRIZON FIOS - URC SETUP CODE LIST FOR TVs


CODE LIST
Admiral 0120, 0490
Advent 0788, 0810, 0842, 0844, 0869
Aiko 0119
Akai 0839, 0729, 0057, 0699
Albatron 0727, 0870
America Action 0207
Ampro 0778
Anam 0207
AOC 0057
Apex Digital 0775, 0906, 0792, 0794
Audiovox 0478, 0207, 0119, 0650, 0829, 0902
Aventura 0198
Bell & Howell 0181
BenQ 1059
Bradford 0207
Broksonic 0263, 0490
Candle 0057
Carnivale 0057
Carver 0081
Celebrity 0027
Celera 0792
Changhong 0792
Citizen 0087, 0057, 0119
Clarion 0207
Commercial
Solutions 1474, 0074
Contec 0207
Craig 0207
Crosley 0081
Crown 0207
Curtis Mathes 0074, 0081, 0181, 0478, 0120, 0087, 0729, 0057, 0172, 0193, 0493, 1174, 1374
CXC 0207
Daewoo 0478, 0119, 1688, 0650, 0688, 0699
Dell 1107, 1205
Denon 0172
Dumont 0044
Durabrand 0490, 0207, 0205, 0198, 1061
Dwin 0747, 0801
Electroband 0027
Electrograph 1782
Emerson 0181, 0263, 0490, 0207, 0205, 0198, 0650
Envision 0057, 0840
Epson 0860, 0867
ESA 0839, 0198
Fisher 0181
Fujitsu 0710, 0836, 0880
Funai 0207, 0198
Futuretech 0207
Gateway 1782, 1783
GE 1474, 0074, 0078, 0478, 0205, 1374
Gibralter 0044, 0057
Go Video 0913
GoldStar 0205, 0057
Grunpy 0207
Haier 1061
Hallmark 0205
Harman Kardon 0081
Harvard 0207
Havermy 0120
Helios 0892
Hello Kitty 0478
Hisense 0775
Hitachi 1172, 0172
Hyundai 0876
Infinity 0081
Insignia 0198
Inteq 0044
JBL 0081
JCB 0027
Jensen 0788, 0842, 0844
JVC 0080, 0758, 1280
KEC 0207
Kenwood 0057
KLH 0792, 0794
KTV 0207, 0057
LG 1292, 0205, 0727, 0883, 1205
LXI 0074, 0081, 0181, 0183, 0205
Magnavox 1481, 0081, 0057, 0733, 0829, 1281
Marantz 0081, 0057, 0731, 0882, 1181
Matsushita 0277, 0677
Maxent 1782
Megapower 0727
Megatron 0205, 0172
Memorex 0181, 0490, 0177, 0205
MGA 0177, 0205, 0057
Midland 0074, 0044, 0078
Mitsubishi 0120, 1277, 0177, 0205, 0863, 0895
Monivision 0727, 0870
Motorola 0120
MTC 0087, 0057
Multitech 0207
NAD 0183, 0205, 0893
NEC 0057, 0524, 0909, 1731
NetTV 1782
Nikko 0205, 0057, 0119
Norcent 0775, 0851
NTC 0119
Onwa 0207
Optimus 0181, 0277, 0193, 0677
Optoma 0914
Optonica 0120 
Orion 0263, 0490, 1490
Panasonic 0277, 0078, 0677, 1437
Penney 0074, 0183, 0078, 0087, 0205, 0057, 1374
Philco 0081, 0057
Philips 1481, 0081, 0717, 1181
Pilot 0057
Pioneer 0193, 0706, 0893
Polaroid 0792, 0892
Portland 0119
Prima 0788, 0810, 0842, 0844
Princeton 0727, 0744
Prism 0078
Proscan 1474, 0074, 1374
Proton 0205, 0493
Pulsar 0044
Quasar 0277, 0078, 0677
RadioShack 0074, 0181, 0207, 0205, 0057
RCA 1474, 0074, 0117, 0706, 1074, 1174, 1274, 1374, 1574
Realistic 0181, 0207, 0205, 0057
Runco 0044, 0057, 0524, 0630
Sampo 0057, 1782
Samsung 0087, 0839, 0729, 0205, 0057, 0793, 0841, 1087
Sansui 0490
Sanyo 0181, 0826, 0920
Scotch 0205
Scott 0263, 0207, 0205
Sears 0074, 0081, 0181, 0183, 0205, 0198
Sharp 0120, 0518, 0715, 0716, 0878
Sheng Chia 0120
Sony 1127, 0027, 0861
Soundesign 0207, 0205
Squareview 0198
SSS 0207
Starlite 0207
Studio Experience 0870
Superscan 0120, 0891
Supreme 0027
SVA 0775, 0892
Sylvania 0081, 0057, 0198
Symphonic 0207, 0198
Tandy 0120
Tatung 1783
Technics 0277, 0078
Techview 0874
Techwood 0078
Teknika 0081, 0207, 0177, 0087, 0119
Telefunken 0729
TMK 0205
TNCi 0044
Toshiba 0181, 1283, 0183, 1292, 0087, 0677, 0859, 0872, 1183, 1383, 1683, 1731
TVS 0490
Vector Research 0057
Victor 0080
Vidikron 0081
Vidtech 0205
Viewsonic 0884, 0891, 0912, 1782
Vizio 0891, 0912, 1783
Wards 0081, 0205, 0057, 0893, 1183
Waycon 0183
Westinghouse 0912, 0916
White Westinghouse 0490, 0650
Yamaha 0057, 0796, 0860, 0866


Zenith 0044, 0490, 1292, 0205, 0119

Wednesday, March 20, 2013

BENQ W1070 - W 1080 ST LAMP REPLACEMENT - LAMP RESET

                                Replacing the lamp


• To reduce the risk of electrical shock, always turn the projector off and disconnect the power cable before changing the lamp.
• To reduce the risk of severe burns, allow the projector to cool for at least 45 minutes before replacing the
lamp.
• To reduce the risk of injuries to fingers and damage to internal components, use caution when removing lamp glass that has shattered into sharp pieces.
• To reduce the risk of injuries to fingers and/or compromising image quality by touching the lens, do not touch the empty lamp compartment when the lamp is removed.
• This lamp contains mercury. Consult your local hazardous waste regulations to dispose of this lamp in a
proper manner. Status Message Install a new lamp for optimal performance. If the projector is normally run with Economics elected , you may continue to operate the projector until the next hour lamp warning appears. Press MODE/ENTER to dismiss the message. It is strongly recommended that you replace the lamp at this stage. The lamp is a consumable item. The lamp brightness diminishes with use. This is normal lamp behavior. You can replace the lamp whenever you notice that the brightness level has significantly diminished. Press MODE/ENTER to dismiss the message. The lamp MUST be replaced before the projector will operate normally. Press MODE/ENTER to dismiss the message.

1. Turn the power off and disconnect the projector from the power outlet. If the lamp is hot, avoid
burns by waiting for approximately 45 minutes until the lamp has cooled.

2. Loosen the screw that secures the lamp cover on the side of the projector until the lamp cover loosens.


3. Remove the lamp cover from the projector.
• Do not turn the power on with the lamp cover removed.
• Do not insert your fingers between the lamp and the projector. The sharp edges inside the projector may cause injuries.



4. Loosen the screw that secures the lamp.
5. Lift the handle so that it stands up.



6. Use the handle to slowly pull the lamp out of the projector.
• Pulling it too quickly may cause the lamp to break and scatter broken glass in the projector.
• Do not place the lamp in locations where water might splash on it, children can reach it, or near flammable materials.
• Do not insert your hands into the projector after the lamp is  removed. If you touch the optical components inside, it could cause color unevenness and distortion of the projected images.

7. As shown in the figure, lower the new lamp.



8. Tighten the screw that secures the lamp.
9. Ensure the handle is fully laid flat and locked in place.
• Loose screw may cause a bad connection, which could result in  Malfunction.
• Do not over tighten the screw.


10. Replace the lamp cover on the projector.


11. Tighten the screw that secures the lamp cover.
• Loose screw may cause a bad connection, which could result in malfunction.
• Do not over tighten the screw.


12. Connect the power and restart the projector.

               Resetting the lamp timer

Do not reset the lamp timer if the lamp has not been replaced as this could cause damage.
13. After the start-up logo, press MENU/EXIT and then press / until the System Setup :
Advanced menu is highlighted.
14. Press to highlight Lamp Settings and press MODE/ENTER. The Lamp Settings page displays.
15. Highlight Reset Lamp Timer and press MODE/ENTER. A warning message displays asking if you
want to reset the lamp timer. Highlight Reset and press MODE/ENTER. The lamp time will be
reset to "0".

                                   

BENQ MS612 ST LAMP REPLACEMENT - LAMP RESET



                                                          Replacing the lamp

• To reduce the risk of electrical shock, always turn the projector off and disconnect the power cord before
changing the lamp.
• To reduce the risk of severe burns, allow the projector to cool for at least 45 minutes before replacing the
lamp.
• To reduce the risk of injuries to fingers and damageto internal components, use caution when removing
lamp glass that has shattered into sharp pieces.
• To reduce the risk of injuries to fingers and/or compromising image quality by touching the lens, do not
touch the empty lamp compartment when the lamp is removed.
• This lamp contains mercury. Consult your local hazardous waste regulations to dispose of this lamp in a
proper manner.
• To assure optimal performance from the projector,it is recommended that you purchase a qualified
projector lamp for lamp replacement.
• If lamp replacement is performed while the projector is suspended upside-down from the ceiling, make
sure that no one is underneath the lamp socket to avoid any possible injury or damage to the human eyes
caused by fractured lamp.

1. Turn the power off and disconnect the projector from the power outlet. If the lamp is hot, avoid burns by waiting for approximately 45 minutes until the lamp has cooled.

2. Loosen the screw(s) that secures the lamp cover on the side of the projector until the lamp cover
loosens


3. Remove the lamp cover from the projector.



• Do not turn the power on with the lamp cover removed.

• Do not insert your fingers between the lamp and the projector.

The sharp edges inside the projector may cause injuries.

4. Disconnect the lamp connector from the projector as illustrated.

5. Loosen the screw that secures the lamp.

6. Lift the handle so that it stands up




7. Use the handle to slowly pull the lamp out of the projector.

• Pulling it too quickly may cause the lamp to break and scatter broken glass in the projector.

• Do not place the lamp in locationswhere water might splash on it, children can reach it, or near flammable materials.

• Do not insert your hands into the projector after the lamp is removed. If you touch the optical components inside, it could cause color unevenness and distortion of the projected images.



8. As shown in the figure, lower the new lamp



9. Tighten the screw that secures the lamp.

10. Ensure the handle is fully laid flat and locked in place.

11. Reconnect the lamp connector.

• Loose screw may cause a bad connection, which could result in malfunction.

• Do not over tighten the screw



12. Replace the lamp cover on the projector.



13. Tighten the screw(s) that secures the lamp cover.

• Loose screw may cause a bad connection, which could result in malfunction.

• Do not over tighten the screw.



14. Connect the power and restart the projector. Do not turn the power on with the lamp cover removed.

                                                      Resetting the lamp timer


15. After the start up logo, open the On-Screen Display (OSD) menu. Go to the SYSTEM SETUP: Advanced> Lamp Settings menu. Press MODE/ENTER. The Lamp Settings page displays. Highlight Reset Lamp Timer. A warning message is displayed asking if you want to reset the lamp timer. Highlight Reset and press MODE/ENTER. The lamp time will be reset to “0”. Do not reset if the lamp is not new or replaced as this could cause damage.
                                       

                          

    

BENQ MX 613 ST LAMP REPLACEMENT - LAMP RESET



                                                          Replacing the lamp

• To reduce the risk of electrical shock, always turn the projector off and disconnect the power cord before
changing the lamp.
• To reduce the risk of severe burns, allow the projector to cool for at least 45 minutes before replacing the
lamp.
• To reduce the risk of injuries to fingers and damageto internal components, use caution when removing
lamp glass that has shattered into sharp pieces.
• To reduce the risk of injuries to fingers and/or compromising image quality by touching the lens, do not
touch the empty lamp compartment when the lamp is removed.
• This lamp contains mercury. Consult your local hazardous waste regulations to dispose of this lamp in a
proper manner.
• To assure optimal performance from the projector,it is recommended that you purchase a qualified
projector lamp for lamp replacement.
• If lamp replacement is performed while the projector is suspended upside-down from the ceiling, make
sure that no one is underneath the lamp socket to avoid any possible injury or damage to the human eyes
caused by fractured lamp.

1. Turn the power off and disconnect the projector from the power outlet. If the lamp is hot, avoid burns by waiting for approximately 45 minutes until the lamp has cooled.

2. Loosen the screw(s) that secures the lamp cover on the side of the projector until the lamp cover
loosens


3. Remove the lamp cover from the projector.



• Do not turn the power on with the lamp cover removed.

• Do not insert your fingers between the lamp and the projector. The sharp edges inside the projector may cause injuries.

4. Disconnect the lamp connector from the projector as illustrated.

5. Loosen the screw that secures the lamp.

6. Lift the handle so that it stands up




7. Use the handle to slowly pull the lamp out of the projector.

• Pulling it too quickly may cause the lamp to break and scatter broken glass in the projector.

• Do not place the lamp in locationswhere water might splash on it, children can reach it, or near flammable materials.

• Do not insert your hands into the projector after the lamp is removed. If you touch the optical components inside, it could cause color unevenness and distortion of the projected images.



8. As shown in the figure, lower the new lamp



9. Tighten the screw that secures the lamp.

10. Ensure the handle is fully laid flat and locked in place.

11. Reconnect the lamp connector.

• Loose screw may cause a bad connection, which could result in malfunction.

• Do not over tighten the screw



12. Replace the lamp cover on the projector.



13. Tighten the screw(s) that secures the lamp cover.

• Loose screw may cause a bad connection, which could result in malfunction.

• Do not over tighten the screw.



14. Connect the power and restart the projector. Do not turn the power on with the lamp cover removed.

                                                      Resetting the lamp timer


15. After the start up logo, open the On-Screen Display (OSD) menu. Go to the SYSTEM SETUP: Advanced> Lamp Settings menu. Press MODE/ENTER. The Lamp Settings page displays. Highlight Reset Lamp Timer. A warning message is displayed asking if you want to reset the lamp timer. Highlight Reset and press MODE/ENTER. The lamp time will be reset to “0”. Do not reset if the lamp is not new or replaced as this could cause damage.
                                                         
                

HOW TO REPLACE LAMP BENQ MX 722 - PROJECTOR - Projector Repair and service - Manual Service


                                               

                                                         Replacing the lamp

• To reduce the risk of electrical shock, always turn the projector off and disconnect the power cord before
changing the lamp.
• To reduce the risk of severe burns, allow the projector to cool for at least 45 minutes before replacing the
lamp.
• To reduce the risk of injuries to fingers and damageto internal components, use caution when removing
lamp glass that has shattered into sharp pieces.
• To reduce the risk of injuries to fingers and/or compromising image quality by touching the lens, do not
touch the empty lamp compartment when the lamp is removed.
• This lamp contains mercury. Consult your local hazardous waste regulations to dispose of this lamp in a
proper manner.
• To assure optimal performance from the projector,it is recommended that you purchase a qualified
projector lamp for lamp replacement.
• If lamp replacement is performed while the projector is suspended upside-down from the ceiling, make
sure that no one is underneath the lamp socket to avoid any possible injury or damage to the human eyes
caused by fractured lamp.
1. Turn the power off and disconnect the projector from the power outlet. If the lamp is hot, avoid burns by waiting for approximately 45 minutes until the lamp has cooled.
2. Loosen the screw(s) that secures the lamp cover on the side of the projector until the lamp cover
loosens

Remove the lamp cover from the projector.


 * Do not turn the power on with the lamp cover removed.
 * Do not insert your fingers between the lamp and the projector.
The sharp edges inside the projector may cause injuries.
 Disconnect the lamp connector from the projector as illustrated.
 Loosen the screw that secures the lamp.
 Lift the handle so that it stands up


 Use the handle to slowly pull the lamp out of the projector.
• Pulling it too quickly may cause the lamp to break and scatter broken glass in the projector.
• Do not place the lamp in locations where water might splash on it, children can reach it, or near flammable materials.
• Do not insert your hands into the projector after the lamp is removed. If you touch the optical components inside, it could cause color unevenness and distortion of the projected images.
As shown in the figure, lower the new lamp
Tighten the screw that secures the lamp.
Ensure the handle is fully laid flat and locked in place.
Reconnect the lamp connector.
• Loose screw may cause a bad connection, which could result in malfunction.
• Do not over tighten the screw

 Replace the lamp cover on the projector.
 Tighten the screw(s) that secures the lamp cover.
• Loose screw may cause a bad connection, which could result in malfunction.
• Do not over tighten the screw.
Connect the power and restart the projector. Do not turn the power on with the lamp cover removed.
                                                      Resetting the lamp timer
15. After the start up logo, open the On-Screen Display (OSD) menu. Go to the SYSTEM SETUP: Advanced> Lamp Settings menu. Press MODE/ENTER. The Lamp Settings page displays. Highlight Reset Lamp Timer. A warning message is displayed asking if you want to reset the lamp timer. Highlight Reset and press MODE/ENTER. The lamp time will be reset to “0”. Do not reset if the lamp is not new or replaced as this could cause damage.